Table of Contents
- How to LED grow light setup for the ball round, bar or panel?
- What is the best brand of LED grow lights?
- What lights do professional growers use?
- Instructions: How to hang & setup LED Grow Light
- Top 5 Best LED Grow Light Review
- How high should I hang my LED grow light?
- LED Grow Light setup grow tent
How to LED grow light setup for the ball round, bar or panel?
#1 How to setup Ball-round LED Grow Lights
The ball round LED Grow lights are a new concept in growing using lights for indoor gardens or grow rooms. They come with the promoted hanging brackets to hang at any of your desired levels according to the lighting needs of your plants. Simply plug the bracket of the Ball round light with the hanging rope that takes hardly minute or two. They are often lightweight and come with 60-100 inches of cord wire that is capable of bearing the weight of the ball lights while use can adjust its hanging height according to the growing needs of the plants, whenever required. The ball round lights are considered ideal for the seedlings and initial vegetative growth of the plants; however, they meet the lighting needs during the entire growth stages of the plants in small areas.
#2 How to setup Bar Grow Lights
LED light bars seem to appear top option for growers due to their effectiveness and broad coverage while their fixing is difficult due to their slender and longer sizes as there is limited space in any grow room but coverage is wider and easily dispersible to the areas you want to lit with. These bars often come with two adjustable brackets that augment the installation procedure with 4 screws to hold them. Fix in screws into the bracket by placing at the points given with holes and insert the desired bars into the brackets. You may use daisy-chaining for hanging lights while their height can be adjusted using a 1/8-inch size of rachet. Tie one end of rachet with the daisy chain and hook another end to the overhead arrangement which will help you to lower or raise the height of height with great ease without touching the light fixtures.
#3 How to setup Grow Lights panel
There is no rocket science required to setup LED panels for the requirements of your plants. LED panel comes with an installation kit and a booklet on how to set up grow lights panels. You need to drill holes for bracketing to hang the cord with the bracket and tying another end to the panel. If they are supposed to be fixed into the frames then you simply need to both brackets into the holes made for this purpose and screw them tightly. Grow light bars can be fixed after you are done with frames to avoid any sort of damage.
What is the best brand of LED grow lights?
There are several brands across different market places but King LED has developed its quality consistently with the constant feedback from its clients and has emerged a leading brand for the most competent and cost-effective LEDs, globally. These LED lights are famous for increasing crop yield and trigger growth of the Cannabis and the plants that need continuous exposure to bright light. Its best replacement of 600 Watts of HPS that uses multiple heat sinks with 2 mute fans whereas the 10-Watt dual-chip LED is made to run for 100, 000 hours to use 185 Watts only. Another good feature is the full spectrum of light similar to that of the sun with both vegetative and bloom switches that can be turned on simultaneously. They also guarantee professional services for 3 years.
What lights do professional growers use?
The LED lights have finally attained equivalence with old-style HID lightings while proving more productive than all existing light systems that were used to grow indoor.
The best-LED lights keep the grow environment cool whereas economically benefitting for running longer in the seen. Professional growers look for the lights with high PPFD ranges between 400-2000μmol/m²/s that provide consistent light through all growing stages of the plants, are more economical, don’t heat up and provides a full spectrum of light for the plants in their grow room.
They also look for the photonic pressure any light yields while in operation as excessive pressures can adverse the yield. Their demands for the full spectrum, high PAR, high PPFD, and low heat are only met through the use of the modern LEDs where they find satisfaction to grow in their grow room, confidently.
Instructions: How to hang & setup LED Grow Light
Here is one of the simplest methods to hang panels to the ceiling or on any of the available racks that would help you to adjust the distance of lights from the plant’s foliage with ease.
#1 What tools are needed to set up?
You may need a screw hook, drill machine, ratchet, screwdriver, and hammer along with Pylons, Adjustable Rope, and Protective glasses that may be ordered before starting set up of the lights in your grow room while these Amazon resources will help you to find the best of its kind.
– For best Self Tapping Screw Hanging Hook measuring 3.54 inches in length.
– For the best Drill Machine with 30 accessories that include screwdrivers bits, magnetic bit holder, nut drivers, and rechargeable batteries. (If you haven’t already)
– For heavy-duty adjustable 1/8-inch rachet, ideal to hang grow lights.
– For Hammers, This Spifflyer 8 OZ Small Claw is best for small jobs.
– Best Rope Hangers for hanging lights.
– For the best protective glasses.
#2 How to hang & setup
Firstly, you are supposed to look for a wooden bean under the plaster of your ceiling to make holes using a drill machine to hook the screws into those holes. A screw hook measuring 3 inches can well hold the weight of the light panel that weighs up to 10 pounds.
Inter connect both loops on one side of the panel to one another and tie the ends into a small rachet. Similarly, interconnect both loops on the other side of the panel and connect into the hook of the racket. Hook the rachet into a hook in the ceiling and adjust the height of your lights. The rachet will help you to lower and raise the height of the panels without touching lights.
You must follow the instruction from the manufacturer for the recommended distance during different stages of the plant’s growth that may vary from 18 inches to 30 inches above the canopy of the plants growing in controlled conditions. Make sure that the inclination of the panels throws sufficient light on the complete foliage of the plants so that they get high PPFD/PAR with a big footprint of the light. If you are supposed to hang a light in a grow tent, repeat the entire practice while instead of hanging to the ceiling, direct the rachet to the frame of the tent. The majority of the grow tents have this provision for hanging grow lights.
Top 5 Best LED Grow Light Review
#1 King Plus 1200 Watts
These LED lights are famous for increasing crop yield and trigger growth of the Cannabis and the plants that need continuous exposure to bright light. It is the best replacement of 600 Watts of HPS that uses multiple heat sinks with 2 mute fans whereas the 10-Watts dual-chip LED are made to run for 100, 000 hours to use 185 Watts only. Another good feature is the full spectrum of light similar to that of the sun with both vegetative and bloom switches that can be turned on simultaneously.
The general recommendation for distance is:
– For Germination, 30-35 inches above the canopy for 14 to 18 hours/day.
– Vegetation, 26-30 inches above the canopy for 14 hours/day.
– For Flowering, 22-30 inches above the canopy for 10 to 12 hours/day.
– For Fruiting, 20-24 inches above the canopy for 8 hours/day.
#2 Spider Farmer SF-2000 Watts
It’s another high energy efficient grow light for commercial growers of the Cannabis and vegetables that take longer to mature. The energy consumption is only 202 Watts while the output is equivalent to 2000 Watts of Blurple light. During the vegetative stage, it can cover up to 3 x 4 feet whereas in the flowering stage 2 x 4 feet area.
It uses SAMSUNG LM301B Diodes for the highest out that can penetrate deeply into the plant canopy for bigger yields backed by MEAN WELL drivers for the safety. No noise as it is without fans while tightly sealed with gum to make it water-proof and shock-resistant.
#3 MARS HYDRO TSW 2000 Watts
It consumes a bit more wattage compared to the similar version of Spider Farmer-2000 while it is perfect for 3.5×3.5 feet during the flowering stage and 4×4 feet for the vegetative stage of the Cannabis plants. It is light of commercial importance while growers adopt this light due to the newest SMD technology that provides the highest PPFD, PAR, and LUMEN.
the inbuilt auto-sensing power works on variable power. i.e. 120, 240, and 277 AC power that suits well to large commercial Cannabis growers. The dimmable option makes easy to adjust brightness for different growing conditions while high Lumen makes your yield perfect under a variety of conditions.
#4 Phlizon Newest 1500W High Power LED
Phlizon Newest 1500W High Power LED is a product that you can rest assured because it does not have any problems with heat dissipation compared to other LEDs of the same capacity. Not only is this LED light affordable, it also provides a full spectrum of light and does a good job of growing plants.
It is a powerful LED compared to a 1000W bulb that consumes 340 Watts, while this LED only consumes 280 Watts.
The best distance from this product to the plant is 24 inches.
#5 Phlizon 2000 Watts
The beauty and the difference with other 2000 watts lights are it is without reflectors that often melt when the temperature rises above the optimum level. They claim it a safety measure that avoids short circuits and breakage in the system. They also use 10 Watts Dual-Chip with high PAR and maximum LUMEN output for which it stays brighter than the traditional lights.
Commercial Cannabis growers love these lights for its full-spectrum and its capacity to keep both vegetative and flowering switches turn on simultaneously. Optimum coverage is 7.2*7.2 feet that extends up to 7.8*7.8 feet if desired.
How high should I hang my LED grow light?
Hanging your LED lights close to the plants may burn them while hanging too for can result in distorted and stunted growth whereas an optimum distance will give your plants the best way to show stunning growth. The care is to be taken that plants receive the amount of light as prescribed by the manufacturer of any LED light. So, if you are supposed to use 2000 Watts light, you must hang it at least 20 inches above the canopy of the plants where it should not be placed more 36 inches away from the upper shoots of the plants. It again depends on the strength of the light as the distance is directly associated with the output of any light that increases with an increase in output and decreases if the output is reduced.
LED Grow Light setup grow tent
All Grow tents contain a rod in the middle of the frame arrangement for hanging grow lights being an essential part for growing inside any tent. You may use two Light Rope Ratchet by hooking each end of the rachet to the back of the light frame first and then to the hook into the frame. Pulling the loose end of the rope in the rachet will raise the level of the light frame and to lower it just release the lock on the rachet, it will slide down gradually.
Rope Ratchet works for you like a rope pulley, locking pully, and adjustable rope hanger for its toughness and makes the operation of light adjustment much easy, as and when desired.